C-K trailer hitch?

Lee Aanderud wrote:
> There was a guy on here a few years ago that fabricated them. I don't have
> contact information.
> http://laanderud.com/hitch/
>
> Lee
>
> "jab-ph" wrote in message
>
>
>>Way back when I had a trailer hitch on one of my '57 GHs. I'd like to
>>find one for my current '58 Hawk. Anyone got a hitch (think my original
>>was a "Draw-Tite") gathering dust?
>
>

If you know a good welder, it probably wouldn't be too hard to just take
some "Z" shaped heavy steel brackets and bolt them to the bumper
mounting points and have them welded to the center section of a typical
receiver hitch. However, the hitch would probably be stronger than the
Stude frame...

I have seen a couple C-K trailer hitches, one of which I actually
contemplated using until I found it was welded to the car on which it
was installed...

nate

--
replace "roosters" with "cox" to reply.
http://members.cox.net/njnagel
 >> Stay informed about: C-K trailer hitch? 

> There was a guy on here a few years ago that fabricated them. I don't
have
> contact information.

Ronnie Scheller rons.DeleteThis@bluevalley.net or 57hawk.DeleteThis@charter.net

I have both email addresses for him in my address book... don't know if one
or both are current.

He (actually his wife) makes a very nice hitch. Hides away nicely behind
the tag when not in use.
--
Dave Lester
Dave's Place
Home of the Internationally Renowned Studebakers, 'Sheba and Goliath
See pictures at www.davesplaceinc.com
 >> Stay informed about: C-K trailer hitch? 

They're very nicely done, I bought one a few years ago but had to send it
back because I didn't know that you had to remove the rear panel underneath
that goes between the tail pipes. He was going to design one that worked
with the panel staying on but I haven't tried to get in touch with him
since. He designs them and his wife cuts and welds them up... and she is a
good welder.

Lee

"Dave's Place" wrote in message

>> There was a guy on here a few years ago that fabricated them. I don't
> have
>> contact information.
>
> Ronnie Scheller rons.TakeThisOut@bluevalley.net or 57hawk.TakeThisOut@charter.net
>
> I have both email addresses for him in my address book... don't know if
> one
> or both are current.
>
> He (actually his wife) makes a very nice hitch. Hides away nicely behind
> the tag when not in use.
> --
> Dave Lester
> Dave's Place
> Home of the Internationally Renowned Studebakers, 'Sheba and Goliath
> See pictures at www.davesplaceinc.com
>
>
 >> Stay informed about: C-K trailer hitch? 

Thx Dave, I'll ty both addresses

Dave's Place wrote:
>>There was a guy on here a few years ago that fabricated them. I don't
>
> have
>
>>contact information.
>
>
> Ronnie Scheller rons.RemoveThis@bluevalley.net or 57hawk.RemoveThis@charter.net
>
> I have both email addresses for him in my address book... don't know if one
> or both are current.
>
> He (actually his wife) makes a very nice hitch. Hides away nicely behind
> the tag when not in use.
 >> Stay informed about: C-K trailer hitch? 

>... and she is a good welder.

She has to be... that's how she makes her living! <G>
--
Dave Lester
Dave's Place
Home of the Internationally Renowned Studebakers, 'Sheba and Goliath
See pictures at www.davesplaceinc.com
 >> Stay informed about: C-K trailer hitch?