Welcome to AutoBoardz.com!
FAQFAQ   SearchSearch      ProfileProfile    Private MessagesPrivate Messages   Log inLog in

Wire Harness Source Needed

  
   AutoBoardz (Home) -> Chrysler RSS
Related Topics:
How to wire??? - on my Jeep 94 Wrangler I need to add lights to a trailer and wiper/ defrost to back window for it, so would like to see a schematic and color code of wiring for this, and would like to know where the wires are? Can anyuone help please?

Pin striping decals needed - Anyone have a source for GOOD decals?? I want them for my PT Cruiser.

What engine needed special low coking oil? - Hey gang. I was reading this group a few months back, and I remember a coming up about a certain Chrysler engine having problems with the timing idler coking up, and breaking the timing I have searched for it on Goggle, but I..

Acclaim 2.5L AIS motor replacement/adjustment HELP needed - Hello I have an Acclaim with 2.4L four, that is idling too high. Found no vacuum leaks. Tested with OTC scanner, idle speed will hover at 1200rpm even when called for base idle (750). I can increase to about 1400 from the scanner, but if I ask for more it

'02 Intrepid Starter Grinding Flywheel - Hi, On cold mornings sometimes my 2002 Dodge Intrepid starter will grind the flywheel. The engine will give a cough that makes me think that maybe the spark is advanced too much for a cold start. Is that possible? The dealer has worked on it twice in less
Next:  2008 Town & Country rear bumper problem  
Author Message
Piperson

External


Since: Jun 10, 2007
Posts: 8



(Msg. 1) Posted: Sun Jul 06, 2008 9:51 am
Post subject: Wire Harness Source Needed Add to elertz
Archived from groups: rec>autos>makers>chrysler (more info?)
I need a wire harness for the front turn signal/emergency/side marker
for a 1999 Chrysler T&C Limited. The part number on the (approx. 30")
cable is 4707837AA 17778C.

Can anyone please point me to a source other than the dealer?

 >> Stay informed about: Wire Harness Source Needed 
Back to top
Login to vote
Bill Putney

External


Since: Feb 25, 2005
Posts: 990



(Msg. 2) Posted: Sun Jul 06, 2008 11:49 am
Post subject: Re: Wire Harness Source Needed Add to elertz [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
Piperson wrote:
> I need a wire harness for the front turn signal/emergency/side marker
> for a 1999 Chrysler T&C Limited. The part number on the (approx. 30")
> cable is 4707837AA 17778C.
>
> Can anyone please point me to a source other than the dealer?

Junk yard?

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')

 >> Stay informed about: Wire Harness Source Needed 
Back to top
Login to vote
maxpower

External


Since: Oct 06, 2004
Posts: 46



(Msg. 3) Posted: Sun Jul 06, 2008 1:50 pm
Post subject: Re: Wire Harness Source Needed Add to elertz [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
"Piperson" <ppsn168.TakeThisOut@yahoo.com> wrote in message
news:v44ck.12192$Fj5.11666@newsfe23.lga...
> I need a wire harness for the front turn signal/emergency/side marker
> for a 1999 Chrysler T&C Limited. The part number on the (approx. 30")
> cable is 4707837AA 17778C.
>
> Can anyone please point me to a source other than the dealer?

Do you need a harness or just the connector???

Glenn Beasley
Chrysler Tech
 >> Stay informed about: Wire Harness Source Needed 
Back to top
Login to vote
Piperson

External


Since: Jun 10, 2007
Posts: 8



(Msg. 4) Posted: Sun Jul 06, 2008 5:06 pm
Post subject: Re: Wire Harness Source Needed Add to elertz [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
Actually, the car side connector is needed. 2 of the 3 wire broke
and/or pulled out of the current one. The plug end is okay except for a
burnt side maker socket. I can live with out that. I am told that
soldering these wires is a pain due to an oxide coating???

On 7/6/2008 1:50 PM, maxpower wrote:
> "Piperson" <ppsn168.TakeThisOut@yahoo.com> wrote in message
> news:v44ck.12192$Fj5.11666@newsfe23.lga...
>> I need a wire harness for the front turn signal/emergency/side marker
>> for a 1999 Chrysler T&C Limited. The part number on the (approx. 30")
>> cable is 4707837AA 17778C.
>>
>> Can anyone please point me to a source other than the dealer?
>
> Do you need a harness or just the connector???
>
> Glenn Beasley
> Chrysler Tech
>
>
 >> Stay informed about: Wire Harness Source Needed 
Back to top
Login to vote
Piperson

External


Since: Jun 10, 2007
Posts: 8



(Msg. 5) Posted: Mon Jul 07, 2008 11:08 pm
Post subject: Re: Wire Harness Source Needed Add to elertz [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
BTW. Another label on the bulb end of the cable indicates

NS JPR PARK/TURN
110722
Assembled in Mexico

There is no label on the car-end connector.

On 7/6/2008 1:50 PM, maxpower wrote:
> "Piperson" <ppsn168.RemoveThis@yahoo.com> wrote in message
> news:v44ck.12192$Fj5.11666@newsfe23.lga...
>> I need a wire harness for the front turn signal/emergency/side marker
>> for a 1999 Chrysler T&C Limited. The part number on the (approx. 30")
>> cable is 4707837AA 17778C.
>>
>> Can anyone please point me to a source other than the dealer?
>
> Do you need a harness or just the connector???
>
> Glenn Beasley
> Chrysler Tech
>
>
 >> Stay informed about: Wire Harness Source Needed 
Back to top
Login to vote
Display posts from previous:   
   AutoBoardz (Home) -> Chrysler All times are: Pacific Time (US & Canada) (change)
Page 1 of 1

 
 You can post new topics in this forum
You can reply to topics in this forum
You can edit your posts in this forum
You can delete your posts in this forum
You can vote in polls in this forum



[ Contact us | Terms of Service/Privacy Policy ]