Dodge Intrepid 3.2L low oil pressure light

Greg Houston wrote:

> I was less than a mile from home when I happened to notice that my oil
> pressure light was on, dimly. I'm not sure how long the light was on
> before I caught it, but I'd guess not long at all. There was no audible
> chime, perhaps the light is controlled by the sensor directly, not
> through the BCM. I stopped with the intent to check the oil level and
> perhaps add some. It was nightime and raining, so I didn't get too far.
> Naturally I was without both my flashlight and phone.
>
> After thinking it over, I decided to continue home. Here's why:
>
> -I recall that some have complained that the oil pressure switch
> failing, which causes the light to come on. Is this a known problem for
> the 3.2L engine, or just the 2.7L? I think there was a TSB for the 2.7.
>
> -The oil light was on dimly, less than full brightness. This seems to
> indicate that it could be a sensor. When the key is on with the
> ignition off, the light is on, full brightness as usual.
>
> -I had less than five minutes of driving and kept it well below 2,000
> rpm. Halfway home from there the light extinguished completely. Hmmm.
> ------
> I recall the dealer changed the oil pressure switch when the car was
> almost brand new because they claimed they saw a leak. Never had a
> problem since. I use Mobil 1 10w30 synthetic oil, and the engine does
> consume oil. Unfortunately a lot of my driving is short trips which
> probably doesn't help that. I'll check the oil level and everything I
> can before starting the engine again.
>
> It was pretty wet out, is it possible this could cause the light to come
> on dimly? Has anyone had the light come on dimly? (may not even be
> visible in daylight) It didn't appear to flicker. The pressure switch
> is either on or off and doesn't provide a range of pressure, right?
>
> Thanks!
> Greg
>
> I also poked around at dodgeintrepid.net but their search function
> appears to be offline.

Hi Greg!

It's the same part on many Chrysler vehicles - definitely all LH's. As
discussed before, it's 90+% certain to be the switch, but to be safe you
should have your pressure checked with a mechanical gage.

It is a switch. I have no definite explanation for the apparent dimness
(instrument brightness control does not affect the warning lights),
unless it is not making the best electrical contact when the pressure is
right on the edge of closing it - there's no hysteresis (snap action) of
the contacts. Or it is flickering (duty cycling) around the closure
point at a rate that makes it appear dim rather than flickering.

There are some that claim that dirt/moisture/corrosion can cause it to
be on intermittently. While that type of leak path might explain the
dimness, I find it hard to believe that it would pull enough current
over the path that it would have to be on to complete the circuit.
While I'm not ruling that out as a possibility, I very much doubt that
to be the problem.

When the switch does go bad on its own, it does behave pretty much as
you described it.

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Possibly a faulty oil sending unit. I have also seen a few problems such as
this (dimmly lit) oil lites and the cause was a shorted circuit board
behind the Instument cluster. Like Bill says, have the oil pressure tested
and you may as well replace the sending unit at that time. If you have good
pressure and the problem persists, have the instument cluster checked out

Glenn Beasley
Chrysler Tech
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

damnnickname wrote:

> Possibly a faulty oil sending unit. I have also seen a few problems such as
> this (dimmly lit) oil lites and the cause was a shorted circuit board
> behind the Instument cluster. Like Bill says, have the oil pressure tested
> and you may as well replace the sending unit at that time. If you have good
> pressure and the problem persists, have the instument cluster checked out

Thanks, Bill and Glenn for your replies!
Update: So far, I haven't had the problem again. The night that the oil light
did go on, I had driven through a puddle in the rain a short time before I saw
the light, so I'm wondering if that is related. I hope it's not the instrument
cluster! I do plan to get the pressure checked.
Are there any tricks to removing the pressure switch? On my 3.2L engine, I
believe it is the green thing that sticks out just below and to the left of the
oil filter. The oil pressure switch part number appears to be 4608303AB (the
AB is new since 2002) and runs about $14-15.

I sure wish it had a pressure guage on the panel to supplement the idiot light.

Thanks,
Greg
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

"Greg Houston" <gh114 DeleteThis @no.spam> wrote in message
news:4554C649.2272E407@no.spam...
> damnnickname wrote:
>
> > Possibly a faulty oil sending unit. I have also seen a few problems such
as
> > this (dimmly lit) oil lites and the cause was a shorted circuit board
> > behind the Instument cluster. Like Bill says, have the oil pressure
tested
> > and you may as well replace the sending unit at that time. If you have
good
> > pressure and the problem persists, have the instument cluster checked
out
>
> Thanks, Bill and Glenn for your replies!
> Update: So far, I haven't had the problem again. The night that the oil
light
> did go on, I had driven through a puddle in the rain a short time before I
saw
> the light, so I'm wondering if that is related. I hope it's not the
instrument
> cluster! I do plan to get the pressure checked.
> Are there any tricks to removing the pressure switch? On my 3.2L engine,
I
> believe it is the green thing that sticks out just below and to the left
of the
> oil filter. The oil pressure switch part number appears to be 4608303AB
(the
> AB is new since 2002) and runs about $14-15.
>
> I sure wish it had a pressure guage on the panel to supplement the idiot
light.
>
> Thanks,
> Greg



When you replace the sending unit take the connector cap off and remove the
rubber seal, slide it up the wire or cut it out. Then replace the sending
unit.

Glenn
>
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

i would do a oil pressure check with a mechincal gauge to make sure there is
not a oil pressure issue there fore maybe saving a expensive engine rebuild
when a oil pump might do the trick or completely rule out a oil pressure issue
out then look at the electrical end of the lite

damnnickname wrote:

> Possibly a faulty oil sending unit. I have also seen a few problems such as
> this (dimmly lit) oil lites and the cause was a shorted circuit board
> behind the Instument cluster. Like Bill says, have the oil pressure tested
> and you may as well replace the sending unit at that time. If you have good
> pressure and the problem persists, have the instument cluster checked out
>
> Glenn Beasley
> Chrysler Tech
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Greg Houston wrote:

> damnnickname wrote:
>
> > Possibly a faulty oil sending unit. I have also seen a few problems such as
> > this (dimmly lit) oil lites and the cause was a shorted circuit board
> > behind the Instument cluster. Like Bill says, have the oil pressure tested
> > and you may as well replace the sending unit at that time. If you have good
> > pressure and the problem persists, have the instument cluster checked out
>
> Thanks, Bill and Glenn for your replies!
> Update: So far, I haven't had the problem again. The night that the oil light
> did go on, I had driven through a puddle in the rain a short time before I saw
> the light, so I'm wondering if that is related. I hope it's not the instrument
> cluster! I do plan to get the pressure checked.
> Are there any tricks to removing the pressure switch? On my 3.2L engine, I
> believe it is the green thing that sticks out just below and to the left of the
> oil filter. The oil pressure switch part number appears to be 4608303AB (the
> AB is new since 2002) and runs about $14-15.
>
> I sure wish it had a pressure guage on the panel to supplement the idiot light.

I went through my records one year after I purchased the car, there was a service
invoce for

-found oil leaking from oil pressure sensor, also found transmission fluid leaking
from trani.
-cooler lines replaced oil pressure sensor tightened
- all clamps for cooler lines cleaned away fluid produced by leaks, roadtest,
rechecked
- found leak at oil cooler line, took part, applied teflon tape, retightened, no
leaks

Under parts, there was a 4608303 (the old part #). All of that was done under
warranty.

I believe I taken it back after an oil change that time because the smell of oil
was strong. I was surprised that they had done all of the above, as after an oil
change the oil that inevitably falls out of the filter being removed spreads all
along those lines, so I always wondered if there were really leaks or some spilled
oil just wasn't cleaned (which I now know isn't easy).
---
I'm debating whether to take the car to the dealer or to a local mechanic...Hmmm
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Bill Putney wrote:

> Greg Houston wrote:
>
>> I was less than a mile from home when I happened to notice that my oil
>> pressure light was on, dimly. I'm not sure how long the light was on
>> before I caught it, but I'd guess not long at all. There was no
>> audible chime, perhaps the light is controlled by the sensor directly,
>> not through the BCM. I stopped with the intent to check the oil level
>> and perhaps add some. It was nightime and raining, so I didn't get
>> too far. Naturally I was without both my flashlight and phone.
>>
>> After thinking it over, I decided to continue home. Here's why:
>>
>> -I recall that some have complained that the oil pressure switch
>> failing, which causes the light to come on. Is this a known problem
>> for the 3.2L engine, or just the 2.7L? I think there was a TSB for
>> the 2.7.
>>
>> -The oil light was on dimly, less than full brightness. This seems to
>> indicate that it could be a sensor. When the key is on with the
>> ignition off, the light is on, full brightness as usual.
>>
>> -I had less than five minutes of driving and kept it well below 2,000
>> rpm. Halfway home from there the light extinguished completely. Hmmm.
>> ------
>> I recall the dealer changed the oil pressure switch when the car was
>> almost brand new because they claimed they saw a leak. Never had a
>> problem since. I use Mobil 1 10w30 synthetic oil, and the engine does
>> consume oil. Unfortunately a lot of my driving is short trips which
>> probably doesn't help that. I'll check the oil level and everything I
>> can before starting the engine again.
>>
>> It was pretty wet out, is it possible this could cause the light to
>> come on dimly? Has anyone had the light come on dimly? (may not even
>> be visible in daylight) It didn't appear to flicker. The pressure
>> switch is either on or off and doesn't provide a range of pressure,
>> right?
>>
>> Thanks!
>> Greg
>>
>> I also poked around at dodgeintrepid.net but their search function
>> appears to be offline.
>
>
> Hi Greg!
>
> It's the same part on many Chrysler vehicles - definitely all LH's. As
> discussed before, it's 90+% certain to be the switch, but to be safe you
> should have your pressure checked with a mechanical gage.
>
> It is a switch. I have no definite explanation for the apparent dimness
> (instrument brightness control does not affect the warning lights),
> unless it is not making the best electrical contact when the pressure is
> right on the edge of closing it - there's no hysteresis (snap action) of
> the contacts. Or it is flickering (duty cycling) around the closure
> point at a rate that makes it appear dim rather than flickering.
>
> There are some that claim that dirt/moisture/corrosion can cause it to
> be on intermittently. While that type of leak path might explain the
> dimness, I find it hard to believe that it would pull enough current
> over the path that it would have to be on to complete the circuit. While
> I'm not ruling that out as a possibility, I very much doubt that to be
> the problem.
>
> When the switch does go bad on its own, it does behave pretty much as
> you described it.

Update: The engine oil pressure appears to be ok. (thank goodness!)
The problem did reoccur, also on a day with heavy rains and a lot of
water on the roads, which leads me to believe there is a connection.

As you might expect, I've been watching that light pretty closely. When
it was on, it was on fairly dim. In daylight it was barely noticeable,
and would have been missed completely if I wasn't watching for it. It
did not appear to be flickering; if it was, it was flickering much
faster than my eyes can see. (And my eyes are bothered by a monitor
with a slow refresh rate.)

I just ordered some parts, including an OEM oil pressure switch. The
part is cheap enough that I hope to replace it at the next oil change
without too much trouble. I'll keep the old one to study it.

I still like my car and hope to get some more years out of it, even
though it will turn eight in just 2.5 months. I'm not even sure what I
would replace it with, the ample capacity and highway economy are a
tough act to follow.

From what I understand about the switch, it closes at just under 5 psi.
The BCM computer is not involved with the light, and it goes out as
soon as pressure rises when the engine is started. Usually it flicker
out just as the tachometer gets to about 1000 rpm, there is probably a
little lag with the switch moving. It comes on a little sooner than the
computer powered lights because it comes on when the key is in the OFF
position, just before you turn the key to ON thence to start. The only
other red or amber warning light that operates in a similar manner is
the brake warning light.

Since oil pressure requirements increase with engine RPM, it would be
nice if a warning light triggered at a higher PSI when the engine is
moving faster, but we can't have everything I guess.
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Greg Houston wrote:

> Bill Putney wrote:
>
>> Greg Houston wrote:
>>
>>> I was less than a mile from home when I happened to notice that my
>>> oil pressure light was on, dimly. I'm not sure how long the light
>>> was on before I caught it, but I'd guess not long at all. There was
>>> no audible chime, perhaps the light is controlled by the sensor
>>> directly, not through the BCM. I stopped with the intent to check
>>> the oil level and perhaps add some. It was nightime and raining, so
>>> I didn't get too far. Naturally I was without both my flashlight and
>>> phone.
>>>
>>> After thinking it over, I decided to continue home. Here's why:
>>>
>>> -I recall that some have complained that the oil pressure switch
>>> failing, which causes the light to come on. Is this a known problem
>>> for the 3.2L engine, or just the 2.7L? I think there was a TSB for
>>> the 2.7.
>>>
>>> -The oil light was on dimly, less than full brightness. This seems
>>> to indicate that it could be a sensor. When the key is on with the
>>> ignition off, the light is on, full brightness as usual.
>>>
>>> -I had less than five minutes of driving and kept it well below 2,000
>>> rpm. Halfway home from there the light extinguished completely. Hmmm.
>>> ------
>>> I recall the dealer changed the oil pressure switch when the car was
>>> almost brand new because they claimed they saw a leak. Never had a
>>> problem since. I use Mobil 1 10w30 synthetic oil, and the engine
>>> does consume oil. Unfortunately a lot of my driving is short trips
>>> which probably doesn't help that. I'll check the oil level and
>>> everything I can before starting the engine again.
>>>
>>> It was pretty wet out, is it possible this could cause the light to
>>> come on dimly? Has anyone had the light come on dimly? (may not even
>>> be visible in daylight) It didn't appear to flicker. The pressure
>>> switch is either on or off and doesn't provide a range of pressure,
>>> right?
>>>
>>> Thanks!
>>> Greg
>>>
>>> I also poked around at dodgeintrepid.net but their search function
>>> appears to be offline.
>>
>>
>>
>> Hi Greg!
>>
>> It's the same part on many Chrysler vehicles - definitely all LH's.
>> As discussed before, it's 90+% certain to be the switch, but to be
>> safe you should have your pressure checked with a mechanical gage.
>>
>> It is a switch. I have no definite explanation for the apparent
>> dimness (instrument brightness control does not affect the warning
>> lights), unless it is not making the best electrical contact when the
>> pressure is right on the edge of closing it - there's no hysteresis
>> (snap action) of the contacts. Or it is flickering (duty cycling)
>> around the closure point at a rate that makes it appear dim rather
>> than flickering.
>>
>> There are some that claim that dirt/moisture/corrosion can cause it to
>> be on intermittently. While that type of leak path might explain the
>> dimness, I find it hard to believe that it would pull enough current
>> over the path that it would have to be on to complete the circuit.
>> While I'm not ruling that out as a possibility, I very much doubt that
>> to be the problem.
>>
>> When the switch does go bad on its own, it does behave pretty much as
>> you described it.
>
>
> Update: The engine oil pressure appears to be ok. (thank goodness!) The
> problem did reoccur, also on a day with heavy rains and a lot of water
> on the roads, which leads me to believe there is a connection.
>
> As you might expect, I've been watching that light pretty closely. When
> it was on, it was on fairly dim. In daylight it was barely noticeable,
> and would have been missed completely if I wasn't watching for it. It
> did not appear to be flickering; if it was, it was flickering much
> faster than my eyes can see. (And my eyes are bothered by a monitor
> with a slow refresh rate.)
>
> I just ordered some parts, including an OEM oil pressure switch. The
> part is cheap enough that I hope to replace it at the next oil change
> without too much trouble. I'll keep the old one to study it.
>
> I still like my car and hope to get some more years out of it, even
> though it will turn eight in just 2.5 months. I'm not even sure what I
> would replace it with, the ample capacity and highway economy are a
> tough act to follow.
>
> From what I understand about the switch, it closes at just under 5 psi.
> The BCM computer is not involved with the light, and it goes out as
> soon as pressure rises when the engine is started. Usually it flicker
> out just as the tachometer gets to about 1000 rpm, there is probably a
> little lag with the switch moving. It comes on a little sooner than the
> computer powered lights because it comes on when the key is in the OFF
> position, just before you turn the key to ON thence to start. The only
> other red or amber warning light that operates in a similar manner is
> the brake warning light.
>
> Since oil pressure requirements increase with engine RPM, it would be
> nice if a warning light triggered at a higher PSI when the engine is
> moving faster, but we can't have everything I guess.

That would be called a gage!

The pressure switches generally get out of calibration when they start
leaking into the connector cavity. The sealed cavity builds up pressure
that works on the opposite side of the diaphragm that actuates the light
switch - so the trip point is effectively shifted higher (i.e, instead
of the original 5 psi, it now takes 7 or so psi to trip it - so the
light comes on during normal but low pressure situations: Warm engine,
in gear, idling. The problem becomes random as the connector cavity
pressure fluctuates due to temperature and the oil slowly leaking into
and back out of the cavity in both directions with engine off and run times.

There is a TSB on this problem that has them replace the pressure switch
*and* replace a seal on one of the unused wire holes in the harness
connector with a "vent tube" - costs about $15 or $20 for a $0.02 piece
of wire with crimp terminal that fits into the connector body like a
regular wire except it only acts as a vent (no electrical connection).
That's kind of a bandaid, since a good (non-leaking) switch will not
exhibit the problem (though there can be some minor temperature effects
due to the air that is contained within the sealed cavity - but probably
not enough effect to be significant).

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Bill Putney wrote:

> Greg Houston wrote:
>
> > Update: The engine oil pressure appears to be ok. (thank goodness!) The
> > problem did reoccur, also on a day with heavy rains and a lot of water
> > on the roads, which leads me to believe there is a connection.
> >
> > As you might expect, I've been watching that light pretty closely. When
> > it was on, it was on fairly dim. In daylight it was barely noticeable,
> > and would have been missed completely if I wasn't watching for it. It
> > did not appear to be flickering; if it was, it was flickering much
> > faster than my eyes can see. (And my eyes are bothered by a monitor
> > with a slow refresh rate.)
> >
> > I just ordered some parts, including an OEM oil pressure switch. The
> > part is cheap enough that I hope to replace it at the next oil change
> > without too much trouble. I'll keep the old one to study it.
> >
> > I still like my car and hope to get some more years out of it, even
> > though it will turn eight in just 2.5 months. I'm not even sure what I
> > would replace it with, the ample capacity and highway economy are a
> > tough act to follow.
> >
> > From what I understand about the switch, it closes at just under 5 psi.
> > The BCM computer is not involved with the light, and it goes out as
> > soon as pressure rises when the engine is started. Usually it flicker
> > out just as the tachometer gets to about 1000 rpm, there is probably a
> > little lag with the switch moving. It comes on a little sooner than the
> > computer powered lights because it comes on when the key is in the OFF
> > position, just before you turn the key to ON thence to start. The only
> > other red or amber warning light that operates in a similar manner is
> > the brake warning light.
> >
> > Since oil pressure requirements increase with engine RPM, it would be
> > nice if a warning light triggered at a higher PSI when the engine is
> > moving faster, but we can't have everything I guess.
>
> That would be called a gage!

Yeah, I thought that sounded familiar.

>
>
> The pressure switches generally get out of calibration when they start
> leaking into the connector cavity. The sealed cavity builds up pressure
> that works on the opposite side of the diaphragm that actuates the light
> switch - so the trip point is effectively shifted higher (i.e, instead
> of the original 5 psi, it now takes 7 or so psi to trip it - so the
> light comes on during normal but low pressure situations: Warm engine,
> in gear, idling. The problem becomes random as the connector cavity
> pressure fluctuates due to temperature and the oil slowly leaking into
> and back out of the cavity in both directions with engine off and run times.
>
> There is a TSB on this problem that has them replace the pressure switch
> *and* replace a seal on one of the unused wire holes in the harness
> connector with a "vent tube" - costs about $15 or $20 for a $0.02 piece
> of wire with crimp terminal that fits into the connector body like a
> regular wire except it only acts as a vent (no electrical connection).
> That's kind of a bandaid, since a good (non-leaking) switch will not
> exhibit the problem (though there can be some minor temperature effects
> due to the air that is contained within the sealed cavity - but probably
> not enough effect to be significant).

Yes, I'm familiar with that TSB, I believe it is 08-36-99. (And bless my
library for having all of the TSBs). It doesn't show up until I search under
2.7L engines, and indeed it seems to only apply to 2.7L engines. I have a
3.2L. However, the pressure switch is the same part number, so go figure. I'm
still curious about the rain/oil pressure light correlation.

The TSB says that allotted time for the repair is just twelve minutes. Good
luck getting the car in the bay and up on the lift, and then down again in that
time, to say nothing of installing that 'vent.'
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Greg Houston wrote:

> I was less than a mile from home when I happened to notice that my oil
> pressure light was on, dimly. I'm not sure how long the light was on
> before I caught it, but I'd guess not long at all. There was no audible
> chime, perhaps the light is controlled by the sensor directly, not
> through the BCM. I stopped with the intent to check the oil level and
> perhaps add some. It was nightime and raining, so I didn't get too far.
> Naturally I was without both my flashlight and phone.
>
> -[snippped]-
>
> It was pretty wet out, is it possible this could cause the light to come
> on dimly?

Update: After several weeks of happily driving without an oil pressure
light, it happened again. It had been raining heavily and I thought I saw
the light on very dimly near the beginning of my drive, but then I didn't
see it again...until....

I hit a puddle on the left side, I heard the splash of water spray from the
wheels and simultaneously the oil light came on, not as dim as it had been
before, but still dimmer than when the key is in the OFF position.

So that all but confirms the problem is caused by water. I recently bought
a MOPAR oil pressure switch for about 12 bucks part # 4608303AB. I plan to
change it at my next oil change, expected later this month. Of course
perhaps the problem is not at the pressure switch, but I think that's a
pretty good guess, especially given its very low location on the 3.2 L
engine. Question: when I replace the switch do I reuse a rubber seal?
The switch just has a connector, no seal, I'm not sure what the other pieces
look like until I get under the car.

Thanks to all who responded, especially Bill and Glenn.
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Greg Houston wrote:
> Greg Houston wrote:
>
>
>>I was less than a mile from home when I happened to notice that my oil
>>pressure light was on, dimly. I'm not sure how long the light was on
>>before I caught it, but I'd guess not long at all. There was no audible
>>chime, perhaps the light is controlled by the sensor directly, not
>>through the BCM. I stopped with the intent to check the oil level and
>>perhaps add some. It was nightime and raining, so I didn't get too far.
>> Naturally I was without both my flashlight and phone.
>>
>> -[snippped]-
>>
>>It was pretty wet out, is it possible this could cause the light to come
>>on dimly?
>
>
> Update: After several weeks of happily driving without an oil pressure
> light, it happened again. It had been raining heavily and I thought I saw
> the light on very dimly near the beginning of my drive, but then I didn't
> see it again...until....
>
> I hit a puddle on the left side, I heard the splash of water spray from the
> wheels and simultaneously the oil light came on, not as dim as it had been
> before, but still dimmer than when the key is in the OFF position.
>
> So that all but confirms the problem is caused by water. I recently bought
> a MOPAR oil pressure switch for about 12 bucks part # 4608303AB. I plan to
> change it at my next oil change, expected later this month. Of course
> perhaps the problem is not at the pressure switch, but I think that's a
> pretty good guess, especially given its very low location on the 3.2 L
> engine. Question: when I replace the switch do I reuse a rubber seal?
> The switch just has a connector, no seal, I'm not sure what the other pieces
> look like until I get under the car.
>
> Thanks to all who responded, especially Bill and Glenn.
>
>

Are you sure that the switch is bad and it's not just shorting the
terminal to ground through the water that's splashed on it? Try some
dielectric grease on the connector and see if that doesn't make the
problem go away.

good luck

nate

--
replace "fly" with "com" to reply.
http://home.comcast.net/~njnagel
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

Greg Houston wrote:
> Greg Houston wrote:
>
>
>>I was less than a mile from home when I happened to notice that my oil
>>pressure light was on, dimly. I'm not sure how long the light was on
>>before I caught it, but I'd guess not long at all. There was no audible
>>chime, perhaps the light is controlled by the sensor directly, not
>>through the BCM. I stopped with the intent to check the oil level and
>>perhaps add some. It was nightime and raining, so I didn't get too far.
>> Naturally I was without both my flashlight and phone.
>>
>> -[snippped]-
>>
>>It was pretty wet out, is it possible this could cause the light to come
>>on dimly?
>
>
> Update: After several weeks of happily driving without an oil pressure
> light, it happened again. It had been raining heavily and I thought I saw
> the light on very dimly near the beginning of my drive, but then I didn't
> see it again...until....
>
> I hit a puddle on the left side, I heard the splash of water spray from the
> wheels and simultaneously the oil light came on, not as dim as it had been
> before, but still dimmer than when the key is in the OFF position.
>
> So that all but confirms the problem is caused by water. I recently bought
> a MOPAR oil pressure switch for about 12 bucks part # 4608303AB. I plan to
> change it at my next oil change, expected later this month. Of course
> perhaps the problem is not at the pressure switch, but I think that's a
> pretty good guess, especially given its very low location on the 3.2 L
> engine. Question: when I replace the switch do I reuse a rubber seal?
> The switch just has a connector, no seal, I'm not sure what the other pieces
> look like until I get under the car.
>
> Thanks to all who responded, especially Bill and Glenn.

Greg - I'm surprised to find that water could make it come on (due to
the current needed to light the bulb and no close direct path to ground)
- others, including Glenn I think, have told me that could happen, but
I've always been skeptical. I guess it's time to start believing it.
You do say it only comes on very dimly, so I can save face.

The rubber seal is built into the harness side of the connector.

Because it does appear to be a water/corrosion situation, be sure to
clean the harness side of the connector (terminal and all surrounding
insulation) real well with a commercial contact cleaner (from auto parts
store) and fill the connector cavity with electrical-grade silicone
grease (in the little condom-type foils on the counter at the auto parts
store) before mating it to the switch.

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light 

"Greg Houston" <gh114.TakeThisOut@no.spam> wrote in message
news:4571DB2F.F6C1074A@no.spam...
> Greg Houston wrote:
>
> > I was less than a mile from home when I happened to notice that my oil
> > pressure light was on, dimly. I'm not sure how long the light was on
> > before I caught it, but I'd guess not long at all. There was no audible
> > chime, perhaps the light is controlled by the sensor directly, not
> > through the BCM. I stopped with the intent to check the oil level and
> > perhaps add some. It was nightime and raining, so I didn't get too far.
> > Naturally I was without both my flashlight and phone.
> >
> > -[snippped]-
> >
> > It was pretty wet out, is it possible this could cause the light to come
> > on dimly?
>
> Update: After several weeks of happily driving without an oil pressure
> light, it happened again. It had been raining heavily and I thought I saw
> the light on very dimly near the beginning of my drive, but then I didn't
> see it again...until....
>
> I hit a puddle on the left side, I heard the splash of water spray from
the
> wheels and simultaneously the oil light came on, not as dim as it had been
> before, but still dimmer than when the key is in the OFF position.
>
> So that all but confirms the problem is caused by water. I recently
bought
> a MOPAR oil pressure switch for about 12 bucks part # 4608303AB. I plan
to
> change it at my next oil change, expected later this month. Of course
> perhaps the problem is not at the pressure switch, but I think that's a
> pretty good guess, especially given its very low location on the 3.2 L
> engine. Question: when I replace the switch do I reuse a rubber seal?
> The switch just has a connector, no seal, I'm not sure what the other
pieces
> look like until I get under the car.
>
> Thanks to all who responded, especially Bill and Glenn.
>
>

The oil switch is actually a pressure transducer, but in order for the
switch to work properly it must be vented to atmosphere. The problem is when
the vent of the switch gets plugs with dirt or any other contaminates such
as oil from the leaking switch. the operation of the switch is altered
because the switch cannot compare the outside air pressure to the oil
pressure created by the engine. clean out the harness end of the switch
thoroughly, I always disassemble the connector and remove the rubber seal or
just pull it back. There was a TSB on this back for the 1999 LH to do this
plus to add a wire terminal vent.. Do this and your problem will be gone..

Glenn
 >> Stay informed about: Dodge Intrepid 3.2L low oil pressure light