96 Accord LX

http://1990-Honda-Accord.autoboardz.com/96-Accord-LX-Headlight-problem-ftopict188836.html (96 Accord LX - Headlight problem)
I lost the passenger-side low-beam headlight on my 1996 Accord LX the otehr day. I bought a couple of new bulbs, and replaced both low-beams. The PS bulb still didn't light. I swapped in the "good" one I pulled from the driver side and it still didn't light. I suspect the connector/wire leavin..
« I believe there is a separate fuse/relay for each bulb. So before you re-wire it, make sure its not just a popped relay or a blown fuse. »
« : Mine has a single fuse for the left, and a single fuse for the right. I put a multimeter on the connector and only got 3V. Pulled on the wire and watched the voltage jump all over the place. .. »
« I looked at a '95 Accord wiring diagram, probably the same as your car, when you pulled the fuse you got a sneak circuit....three filiments in series. The low beam lights are grounded to the chassis.. »
« ====================== Dave, I think you're describing the symptoms of a missing ground. Check the ground side of the circuit, and try using a 12 volt bulb as a tester, if you need to. Since the m.. »

http://1990-Honda-Accord.autoboardz.com/96-Accord-LX-Front-Rotor-Removal-ftopict188841.html (96 Accord LX Front Rotor Removal ???)
There are four bolts on the front rotors (besides the studs). Will the rotor come off after removing these? My '91 had the rotors pressed on. Looks like I can get these off myself. Correct? G-Man
« Do a search on dejanews.com and you will find much discussion on your question. You need to take that big hub nut off which is torqued around 200 lbs I think. I'd like to know if anyone has done i.. »
« I tried to remove that hub nut with a hydraulic floor jack under a ratchet wrench, and all I managed to do was break the wrench. I tried it with a regular fixed wrench, and when it started to bend.. »
« I looked and the big nut does not seem to be part of the stuff holding the rotor on. Maybe I'm wrong, but that's how it looks. G-Man »
« Looks like the bastard is pressed on. Off to the shop if I have to replace them Haven't measured them, but 146k on the car and they've never been replaced. They don't pulse, so I may just go ne.. »

http://1990-Honda-Accord.autoboardz.com/96-Accord-LX-Intermittent-Speedometer-issue-ftopict188855.html ([96 Accord LX] Intermittent Speedometer issue)
Hello, The speedometer on my 96 Accord LX has started to behave erratically. Sometimes it will work fine. Other times it will appear dead and come to life after the car has been driven a while. Other times it will start and stop randomly while driving. The odometer seems to be working fine thou..
« if the odometer is working fine then I would think the speed sensor is ok because I believe it utilizes the same input for both. I might be inclined to believe the actual speedometer unit itself .. »
« I have an old honda have same problem. »
« The electroinis in the speedo have gone bad. If the sendsor was screwy you wouldnt gat an odometer reading AND the check engine light would come on since it does use speed as one of the computers .. »
« erratically. I had this problem with my '96 Civic. I replaced the speedo unit with one from a junkyard (found online for $65.) I later had the same problem with the new unit and it turned out to b.. »

http://1990-Honda-Accord.autoboardz.com/Front-end-ftopict192650.html (Front end Question)
96 Accord LX 5 spd. When I am driving, the wheel seems to "feel" every nook and lump in the road... I just replaced the Upper control arm ball joint, the brakes are working fine. There is a lot of bearing howl in the front, but no loose play in the wheels when jacked up.. So my question is: Be..
« Is it possible it's tire trouble? Mike »
« Tires are fairly new , and this problem has gotten gradually worse over the last month. Another reader suggested it may be the stabilizer bar bushings and I think he may have something there... Th.. »

http://1990-Honda-Accord.autoboardz.com/Transmission-Replacement-ftopict200563.html (Transmission Replacement)
96 Accord LX 156,000 Last week my transmission went out on me completely. Tranny was slipping out of gear for a while (but was not sure what was happening) then this past Monday tranny went out on me while driving (fortunately was not to far from my mechanic's shop) had to crawl over to my mechan..
« : You need to get the error code(s) read from the Check Engine light. If you have a 4-cylinder and an error code of P0740, there is a TSB that may apply. There may be more TSBs, but for that you'd .. »
« Is this mechanic a Honda specialist? Does he work on Hondas every day and stay up to date on TSBs, etc? If so, perhaps he is correct that you need a new tranny. It is also possible that someth.. »
« Is this mechanic a Honda specialist? Does he work on Hondas every day and stay up to date on TSBs, etc? Yes, he is a Honda specialist, he only works on Honda and Acura and I have been going to him f.. »

http://1990-Honda-Accord.autoboardz.com/96-Accord-LX-2l-MFI-ftopict209677.html (96 Accord LX 2.2l MFI AT)
Hi guys, was really hoping you can help me out! Was driving home today and the tranny started slipping. Then the CEL came on. I pulled over, turned the car off, then restarted it, drove fine for about 5 minutes. Started slipping again. Turned off, turned on, driving fine again. I had the cod..
« Anyone? Brice »
« Is it only one certain gear it slips in? »